I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Istruzioni di installazione
Installatie-instructies
Instruções de Instalação
Instructions d´installation
Keyboard Tray Accessory
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
KSA1021
Installation Instructions
KSA1021
LEGEND
Tighten Fastener
Hex-Head Wrench
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Zeskantsleutel
Clé à tête hexagonale
ɋɨɠɦɢɬɟꢀɁɚɫɬɟɠɤɭ
Ʉɥɸɱꢀɫꢀɲɟɫɬɢɝɪɚɧɧɨɣꢀɝɨɥɨɜɤɨɣ
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
ɈɫɥɚɛɶɬɟꢀɁɚɫɬɟɠɤɭ
TOOLS REQUIRED FOR INSTALLATION AND PARTS
1/4" (provided)
C (1)
E (2)
B (1)
D (1)
F (1)
H (1)
G (1)
A (1)
J (1)
3
KSA1021
Installation Instructions
6. Slide height adjustable arm with spacer and UHM washer
(B) in between mounting tabs in vertical tray mounting
bracket(H)until mountingholesinarmandbracketalign.
(See Figure 1)
7. Place UHM washer, removed during step 1, over mounting
hole in upper mounting tab of vertical tray mounting bracket.
(H).
8. Slide spacer, removed during step 1, down through UHM
washer and mounting hole in vertical tray mounting bracket
(H) and into height adjustable arm. (See Figure 1)
INSTALLATION
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! DO NOT substitute
hardware. Only use hardware provided or specified by
manufacturer.
1. Remove hardware securing Centris head assembly to
height adjustable arm.
2. Set hardware aside for re-use.
9. Place two flat washers and one Nylon washer, removed
during step 1, onto socket head screw (J) provided with tray
accessory. (See Figure 1)
10. Align mounting hole in Centris head assembly with
mounting hole in vertical tray mounting bracket (H).
11. Slide socket head screw (J) with washers down through
Centris head assembly and height adjustable arm.
IMPORTANT ! : DO NOT DISCARD HARDWARE!
Hardware will be used when installing laptop tray
accessory.
3. Orient vertical tray mounting bracket as show in figure
below. (See Figure 1)
4. Slide spacer (C) into bottom of height adjustable arm.
5. Place UHM washer (B) on upper area of height adjustable
arm.
12. Hold hex nut, removed during step 1, in bottom of height
adjustable arm and secure Centris head assembly and
vertical tray mounting bracket (H) to height adjustable arm
by tightening socket head screw (J) using 1/4" hex wrench.
(D) x 1
9
8
(B) x 1
1
7
5
(H) x 1
3
6
4
12
(C) x 1
Figure 1
4
Installation Instructions
KSA1021
13. Orient horizontal tray mounting bracket (G) as shown in
figure below. (See Figure 2)
14. Secure horizontal tray mounting bracket (G) to vertical tray
mounting bracket (H) using one carriage bolt (J) and one
knob (E). (See Figure 2)
15
(A) x 1
(G) x 1
(H) x 1
(E) x 1
(J) x 1
Figure 3
14
(G) x 1
13
(E) x 1
Figure 2
15. Orient tray (A) as shown. (See Figure 3)
16. Secure tray (A) to horizontal tray mounting bracket (G)
using one knob (E). (See Figure 3)
5
KSA1021
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 40 2668620
+31 (0) 40 2668615
Asia Pacific
A
Room 30I, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112
8804-000355
¤2007 Chief Manufacturing
10/07
P
F
+86-755-8996 9226 ; 8996 9236 ; 8996 9220
+86-755-8996 9217
|